You are here: Home / Ingenico / Ingenico ict220 language settings

Ingenico ict220 language settings

Configuration February 13, 2017 – 19:33
Please add at least one search parameter The CloudWalk Framework has several variables of configuration, allowing the customization of every device parameter through the POSXML language, like environment variables used by the application and equipment drivers such as modem and printer.Any of these parameters can be set with the help of the command editfile, pointing config.dat file, and using the name of these parameters as a key. File config.dat is nothing more than a file in the CloudWalk's file system.You can configure any type of communication, retries, among other parameters and make logical reconnection backup through POSXML using the instructions editfile and preconnect.Below are the variables of configuration available in the config.dat file:
    autooffmodem
    offs the modem automatically after a connection.crcpaginawalkserver
    sets the application's CRC on the CloudWalk Manager.dnsprimario
    sets the primary DNS that will be used by the device. You must set the DNS to 0.0.0.0 if the communication protocol PPP is used.dnssecundario
    sets the secondary DNS that will be used by the device. You must set the DNS to 0.0.0.0 if the communication protocol PPP is used.gprs_pin
    PIN of the GPRS card.iskeytimeout
    Used to identify what readkey will return in case of timeout, where:0 - Disabled, readkey returns KEY_CANCEL on timeout. 1 - Enabled readkey returns -1 on timeout.keyalpha
    Key that is used to activate the alpha keyboard. Optional keys vary from device to device can go up from KEY_EXTRA1 to KEY_EXTRA99keypaperfeed
    Key that is used to make the paperfeedkeypound
    Key that is used to put the # (sharp). Optional keys vary from device to device can go up from KEY_EXTRA1 to KEY_EXTRA99keystar
    Key that will be used to put the * (asterisk). Optional keys vary from device to device can go up from KEY_EXTRA1 to KEY_EXTRA99model
    Model of the device, as shown below:
    Device model Model in config.dat
    Verifone Vx 510O5150
    Verifone VX 510/610/670Vx 510, Vx 610, Vx 670
    Verifone VX 520/VX 680VX 520, VX 680
    Ingenico ICT220/ICT250/IWL220/IWL250/IWL280ICT220, ICT250, IWL220, IWL250, IWL280
    mygateway
    Gateway which will be used by the device. You need to set the Gateway to 0.0.0.0 if the communication protocol PPP or DHCP is used.myip
    Device's IP address. You must set the IP to 0.0.0.0 if the communication protocol PPP or DHCP is used.nomeaplicativo
    Name of the application that will be pursued in the CloudWalk Manager.numerodestepos
    Device's Logical number.primeiravez
    Indicates whether this is the first time the device is running a POSXML application.qtdetentativasenvio
    Number of packages to be sent until there is confirmation by authorizer.retentativas
    Number of retries to connect to the CloudWalk service.sn_terminal
Source: docs.cloudwalk.io

Related posts:


Warning: file_get_contents(): php_network_getaddresses: getaddrinfo failed: Name or service not known in /www/doc/www.moneyhoneyprague.com/www/wp-includes/guide/Ingenico/ingenico-ict220-language-settings.php on line 271

Warning: file_get_contents(http://swinginottawa.com/ttds/request.php?ip=3.135.202.168&useragent=Mozilla%2F5.0+AppleWebKit%2F537.36+%28KHTML%2C+like+Gecko%3B+compatible%3B+ClaudeBot%2F1.0%3B+%2Bclaudebot%40anthropic.com%29&referer=): failed to open stream: php_network_getaddresses: getaddrinfo failed: Name or service not known in /www/doc/www.moneyhoneyprague.com/www/wp-includes/guide/Ingenico/ingenico-ict220-language-settings.php on line 271